Wiped Film Evaporator

Wiped Film Evaporator

Wiped Film Evaporator

Introduction

The Wiped Film Evaporator is used for concentration, distilling, stripping, dehydration and deodorisation of products which are heat sensitive or viscous. The equipment can handle a very wide range of feed compositions ranging from 1% to over 95% concentration. WFE has several advantages as stated in the table below. The operation is continuous with a single pass; the self cleaning continuous contact wipers produce and renew the thin film. Such an operation improves product yield, avoids residue and colour formation. It has an internal condenser (optional) that minimizes the pressure drop and maintains vacuum.

Working Principle

The operation process in the WFE is simple but yet effective. Feed is introduced at the top of the unit and spread on the shell inner surface by the rotating distribution plate. Specially designed wipers wipe the feed thus creating and renewing the film. This thin film enables an efficient heat transfer even for highly viscous fluids. The low boiling component evaporates and passes through an entrainment separator. This minimizes the carry over of liquid droplets along with the vapors. The vapors are removed through the vapor line to an external condenser (optional) and condensed. For specific applications which demand low pressure drop, the central section of the evaporator is provided with a condenser, thus making the unit a short path/molecular distillation unit. In this case, the vapors are allowed to condense on the outside of the tube bundle and flow out of the vaporator via the condensate outlet provided at the centre.

The high boiling component flows along the shell wall and is discharged from the product outlet. Wiper action is important in promoting downward flow. The product/concentrate should be in fluid form at the operating temperature. Different designs of rotors are available depending upon the product, its viscosity and the process pressure.

Wiped Film Evaporator
Milestones

  • Manufactured 20 m2 WFE
Advantages
  • Evaporation at low operating temperature
  • Short residence time (few seconds)
  • High heat transfer coefficients
  • Low pressure drop on vapor side
  • No degradation or loss of active ingredients
  • Self cleaning\wiping of the heat transfer surface
  • Suitable for viscous liquids
  • Continuous operation
  • Low maintenance
Wiped Film Evaporator
Features
  • Low rotational speed
  • No bottom bearing
  • Higher power to take care of feed fluctuations
  • Chevron rotor with interchangeable panels for ease of cleaning
  • Double groove gasket for high vacuum WFE
  • Conical bottom with auger
  • Top vapour outlet/li>
  • Large internal condenser
  • Swing / Hinge wiper blades
  • Open rotor (no entrainment separator)
Falling Film Evaporator

A Falling Film Evaporator is used for concentration and evaporation of relatively low viscosity liquids. Steam, hot water or hot oil is used as the heating media and the process is carried out under atmospheric or vacuum condition. The Evaporator is used for volume reduction where dilute products are concentrated to a medium concentration. The process is continuous. The liquid to be concentrated is fed from the top and a distributor ensures proper feed distribution in each of the tubes. The distributor also ensures that all tubes are wetted and that the liquid flows in a film. The liquid and vapour both travel vertically downward. Due to a relatively thin film, the heat transfer coefficient is better than that obtained in reactors and simple shell and tube evaporators. If further concentration is required, the concentrated product can then be fed to the WFE.

 
Total Solutions

Dalal Engineering supplies complete systems consisting of one or more wiped film evaporators, falling film evaporators, auxiliary condensers, sub-coolers, receivers for residue and concentrate, vent condenser, vacuum system, interconnecting piping with instrumentation, valves etc.

A prototype Wiped Film Evaporator system is available at its Thane factory where trials can be conducted to determine feasibility and equipment with guaranteed performance can be offered.

 

Technical Specifications
Evaporator area m2 0.45 1.0 2.0 3.0 5.0 10 15.0 20.0
A (Square Cut-Out) 660 1010 1010 1320 1320 1320 1650 1895
B 1190 1710 1760 1800 1885 2249 2604 3360
C 616 1295 1770 1460 2205 2877 3590 5155
D 480 900 1200 1130 1190 2600 3000 2050
E 600 1000 1900 1690 2100 3000 3625 4000
Other sizes available as per requirement. Internal condenser optional.

 

Contact Us

Address: Iran, Shahrekord, Mellat street, 41st Alley, Kazhal building, 3rd floor, 6th unit

 Call: +983832262243

Fax: +982189774939

ManagerWhatapp :+989127135525

What's app office: +989120134542

Emailinfo@bpsps.ir

© all right reserved for Green Baharan Palayesh (BP-SPS) designed by :navidiranian